How to Get Galaxy S5 Screen Adhesive to Stick Again
How to Ready Cleaved Milky way S5 Screen and Other Parts after Teardown
BY yuki | May 10th, 2014 | | 4
Although many reports claimed that it's harder to repair Milky way S5 than S4, information technology gets 5 out of ten (10 is the easiest to repair). Therefore, compared with other smartphones, Milky way S5 is not difficult to repair. Hither we walk yous through detailed steps for replacing a cracked Galaxy S5 screen, damaged GS5 camera, broken S5 loudspeaker, eye frame etc. ETrade Supply is always your prior option to get Samsung Galaxy S5 replacement parts and components.
Please note the DIY repair will void the warranty of your Galaxy S5 merely may salve money. Watch the following stride-by-step GS5 teardown tutorial to find how to repair your Galaxy S5 screen and other parts and components showed in beneath.
• Replace a cracked or shattered Galaxy S5 screen
• Fix a damaged Galaxy S5 battery
• Supplant cleaved Samsung Galaxy S5 photographic camera
• Set malfunctioned Galaxy S5 ear speaker or loudspeaker
• Repair a broken GS5 battery door or problematic rear housing
• Fix a damaged Galaxy S5 earphone jack
• Repair a problematic Galaxy S5 charging port
Tools needed to disassemble Samsung Milky way S5
Hair Dryer
Modest Phillips Screw commuter
Plastic Spudger
Suction Cup Tool
Several Example Opening Cost
Tweezers
Footstep one: Ability off the Samsung Galaxy S5.
Stride 2: Remove the GS5 battery door with your pollex.
Note: If your GS5 back cover is broken, you tin can supersede it with a new back panel at this step.
Step 3: Peel the Galaxy S5 battery off.
Note: If you suffer a damaged Galaxy S5 battery, you lot can purchase a new one and set it past replacing information technology at this footstep. However, please accept intendance to check if the Samsung Milky way S5 battery you purchase is genuine, for a fake battery may trigger an explosion. (Here is practiced tutorial: How to Place the Original and Fake Cellphone Battery)
Step 4: Remove the comprehend protecting the connector underneath it.
Note: Do not use sharp tweezers which volition impairment the plastic encompass.
Step 5: Disconnect the Milky way S5 home push connector.
Footstep 6: Use a hair dryer to heat up the Milky way S5 screen.
The Galaxy S5 LCD screen and digitizer bear upon screen assembly is firmly glued to the rear housing by pasty adhesive, so you have to rut upwards the screen of Galaxy S5 with a hair dryer or oestrus gun. Make the screen hot plenty until the glue is loose.
Step vii: Use the plastic spudger to pry the Galaxy S5 screen and wedge several case opening tools around the side.
Annotation: Do not pry the Milky way S5 screen from the lesser of the phone, because the GS5 home button, back push button and bill of fare button locate at the lesser. Also, you have to be aware there is a flex cablevision connecting the LCD screen and digitizer and mainboard at the upper side of the screen component, so practice not push button too deeply when you lot disassemble the tape with the spudger tool.
Step 8: Disconnect the flex cable of Galaxy S5 screen assembly connecting the LCD screen and digitizer to the mother lath.
Notation: When there is a gap between the Galaxy S5 LCD screen associates and the rear housing, you lot tin can use a plastic spudger to disconnect the GS5 screen assembly flex cablevision.
Footstep 9: Separate the Galaxy S5 screen associates from the rear housing. You need to disassemble the Braket Cu tape carefully from the S5 LCD assembly.
Annotation: you desire to replace any of the Milky way S5 internals, yous have to go through the screen removal process at commencement. After free the display assembly on Galaxy S5, other role replacements are very easy.
Step x: The Samsung Galaxy S5 LCD screen and digitizer associates is separated from the rear housing.
Note: At this pace, the Galaxy S5 screen is removed. If your Galaxy S5 screen is shattered or broken, yous can supercede a new one. Simply please kindly note the Galaxy S5 domicile button is attached to the screen. You tin can buy a new GS5 screen with domicile button, if not, you lot have to remove the home button from the broken screen and install information technology to the new i you buy. Also, if your GS5 dwelling button is broken, you can supersede it at this stride too.
Stride xi: The form tape on the back of GS5 LCD assembly must be inverse to the new one whenever reassembled.
Note: When the Milky way S5 is disassembled, the water resistance performance would exist affected. Therefore, you should change the course tape or Galaxy S5 front housing adhesive to a new one to better warranty the characteristic.
Step 12: You need to remove the residue of form record on the Milky way S5 rear housing with cary jig & rework tape.
Note: It is necessary to make clean the form tape residuum which will affect water resistance functioning.
Step 13: Remove the Galaxy S5 Bracket Cu tape.
Note: This Bracket Cu record is helpful for water resistance functioning, and it must exist replaced to the new one whenever reassembled to provide a ameliorate warranty on water resistance.
Step 14: Unscrew 10 screws holding the middle frame and rear frame on the Galaxy S5 front side.
Note: When you lot detach Milky way S5, these 10 screws should be replaced to the new one, in gild to guarantee the water-resistant office.
Pace fifteen: Unscrew three screws at the back of the Galaxy S5.
Note: Whenever reassembled Milky way S5, these 3 screws should be replaced to the new ane for water resistance operation.
Step 16: Pull the rear frame out of centre frame on Galaxy S5. Y'all can start the chore from the elevation.
Note: You also tin separate out the Milky way S5 eye frame with the help of case opening tool. The Milky way S5 motherboard is fixed to the middle plate.
Footstep 17: The Galaxy S5 rear housing is removed from the middle plate.
Footstep 18: Peel off the Samsung Milky way S5 ear phone jack with tweezers.
Step 19: Remove the Galaxy S5 loud speaker with the help of tweezers.
Footstep 20: Unscrew 2 screws securing the Galaxy S5 mainboard to the frame.
Footstep 21: Disconnect the antennas on Galaxy S5 connecting the charging port to the mainboard.
Step 22: Separate the Galaxy S5 motherboard from rear housing.
Footstep 23: Lift up the Samsung Milky way S5 rear-facing photographic camera which is attached to the mainboard.
Pace 24: Pare off the Samsung Milky way S5 front-facing camera with spudger.
Pace 25: Remove the Galaxy S5 charging port with the menu button, back button, and fingerprint scanner.
Note: Yous may supercede the charging port the almost often on the phone besides the croaky screen. And so at this footstep, you can replace a new charging port by follow the instructions.
Footstep 26: Peel off the Milky way S5 vibrating motor with tweezers.
Pace 27: Pace-by-step Samsung Galaxy S5 disassembly job is finished.
Samsung Galaxy S5 comes with the new water resistance functioning. Even so, if your Milky way S5 suffers breakage and need to exist repaired, you have to be aware of some non-reusable parts that must exist replaced to the new one when reassemble.
These parts are:
Galaxy S5 front housing adhesive / form tap
Galaxy S5 Subclass Cu tape
10 screws on the middle frame
3 screws on the rear housing.
Does this Galaxy S5 teardown tutorial helpful for your S5 parts repair? What problems have you met when you fix cracked Galaxy S5 screens and parts? Allow us know in the comments.
We have worked out the Samsung Galaxy S5 pace-by-stride disassembly video for your reference.
Source: https://www.etradesupply.com/blog/how-to-repair-damaged-samsung-galaxy-s5-screen-and-other-parts-after-disassembly/
0 Response to "How to Get Galaxy S5 Screen Adhesive to Stick Again"
Post a Comment